dienelectrics@gmail.com
0909186879 dienelectrics@gmail.com
Unless explicitly specified otherwise, the following technical specifications are valid for all components of the SINAMICS S120 booksize drive system.
Note:
When engineering the complete SINAMICS S120 drive, the system data of the associated Control Units, supplementary system components, DC link components and Sensor Modules must be taken into consideration.
|
Electrical specifications |
|||
|
Line voltage |
380 ... 480 V 3 AC ±10 % (-15 % <1 min) |
||
|
Line system configurations |
Grounded TN/TT systems and non-grounded IT systems |
||
|
Line frequency |
47 ... 63 Hz |
||
|
Electronics power supply |
24 V DC -15 %/+20 %1), safety extra low-voltage (PELV/SELV) |
||
|
Short-circuit current rating (SCCR) (Short Circuit Current Rating) |
1.1 ... 447 kW: 65 kA |
||
|
Electromagnetic compatibility According to EN 61800‑3 |
Second environment, Category C2/C3 For further information, see section Configuration notes |
||
|
Overvoltage category According to IEC/EN 61800‑5‑1 |
III |
||
|
Mechanical specifications |
|||
|
Degree of protection |
|
||
|
IP20 |
||
|
Open type |
||
|
Protection class |
|
||
|
I |
||
|
Safety extra low-voltage PELV/SELV |
||
|
Ambient conditions |
|||
|
|
Storage |
Transport |
Operation |
|
In product packaging |
In transport packaging |
|
|
|
Climatic environmental conditions |
Class 1K4 |
Class 2K4 |
Class 3K3 3) Relative humidity 5 ... 95 % |
|
Environmental class/harmful chemical substances |
Class 1C2 |
Class 2C2 |
Class 3C2 |
|
Organic/biological influences |
Class 1B1 |
Class 2B1 |
Class 3B1 |
|
Pollution degree 2) acc. to IEC/EN 61800‑5‑1 |
2 |
||
|
Installation altitude |
|
||
|
Without derating |
||
|
|
||
|
|
||
|
and additionally:
|
||
|
|
||
|
Mechanical strength |
|||
|
|
Storage |
Transport |
Operation |
|
In product packaging |
In transport packaging |
|
|
|
Vibratory load |
Class 1M2 |
Class 2M3 |
Class 3M1 |
|
Shock load |
Class 1M2 |
Class 2M3 |
Class 3M1 |
|
Certificates |
|||
|
Declarations of conformity |
CE (Low Voltage, EMC and Machinery Directive) |
||
|
Certificates of suitability |
cULus |
||
1) When using a motor holding brake, restricted voltage tolerances (24 V ±10 %) might need to be taken into account.
2) The components must be protected against conductive pollution, e.g. by installing them in a control cabinet with degree of protection IP54 according to IEC 60529 or NEMA 12. If conductive pollution can be excluded at the installation site, a lower degree of cabinet protection is permissible.
3) Better than 3K3 through increased ruggedness regarding the temperature range and humidity. Oil mist, salt mist, ice formation, condensation, dripping water, spraying water, splashing water and water jets are not permitted.
4) Also carefully observe the permissible temperatures for the Control Unit and operator panel.
In conjunction with Active Interface Modules and a logically consistent configuration of the plant or system, line filters limit the interference conducted by the power modules to the limit values of Category C2 acc. to EN 61800‑3. Line filters are only suitable for direct connection to TN line systems.
Note:
According to product standard EN 61800‑3, RFI suppression commensurate with the relevant rated conditions must be provided and is a legal requirement in the EU (EMC Directive). Line filters and line reactors are required for this purpose. The use of line filters of other makes can lead to limit value violations, resonance, overvoltages and irreparable damage to motors or other equipment. The machine manufacturer must provide verification that the machinery to be operated with the drive products and the installed suppression elements, e.g. line filters, are CE-EMC-compliant.
Optional Basic Line Filters that are coordinated with the power ranges in booksize format are available for the SINAMICS S120 drive system.
With the Basic Line Filters in combination with the Active Interface Modules, the limits for the interference voltages can be extended to Category C2 (EN 61800-3) or, retaining Category C3, longer total cable lengths are possible for the configuration.
Basic Line Filters are used on machines on which conducted interference emissions in the frequency range between 150 kHz and 30 MHz need to be damped in accordance with the requirements of CE-EMC legislation.
|
Line voltage 380 ... 480 V 3 AC |
Basic Line Filter |
|||||
|---|---|---|---|---|---|---|
|
|
6SL3000-0BE21-6DA0 |
6SL3000-0BE23-6DA1 |
6SL3000-0BE25-5DA0 |
6SL3000-0BE28-0DA0 |
6SL3000-0BE31-2DA0 |
|
|
Rated current |
A |
36 |
74 |
105 |
132 |
192 |
|
Power loss |
kW |
0.016 |
0.02 |
0.043 |
0.056 |
0.073 |
|
Line supply/load connection L1, L2, L3 / U, V, W |
|
Screw terminals |
Screw terminals |
Screw terminals |
Screw terminals |
Screw terminals |
|
mm2 |
10 |
35 |
50 |
95 |
95 |
|
PE connection |
|
M6 screw studs according to DIN 46234 |
M6 screw studs according to DIN 46234 |
M8 screw studs according to DIN 46234 |
M10 screw studs according to DIN 46234 |
M10 screw studs according to DIN 46234 |
|
Degree of protection |
|
IP20 |
IP20 |
IP20 |
IP20 |
IP20 |
|
Dimensions |
|
|
|
|
|
|
|
mm (in) |
50 (1.97) |
75 (2.95) |
100 (3.94) |
150 (5.91) |
150 (5.91) |
|
mm (in) |
429 (16.89) |
433 (17.05) |
466 (18.35) |
479 (18.86) |
479 (18.86) |
|
mm (in) |
226 (8.90) |
226 (8.90) |
226 (8.90) |
226 (8.90) |
226 (8.90) |
|
Weight, approx. |
kg (lb) |
5 (11.0) |
7.5 (16.5) |
11.5 (25.4) |
17.5 (38.6) |
18.5 (40.8) |
|
Certificate of suitability |
|
cURus |
cURus |
cURus |
cURus |
cURus |
|
Suitable for Active Line Module in booksize format |
Type |
6SL3130-7TE21-6AA4 |
6SL3130-7TE23-6AA3 |
6SL3130-7TE25-5AA3 |
6SL3130-7TE28-0AA3 |
6SL3130-7TE31-2AA3 |
|
kW (hp) |
16 (18) |
36 (40) |
55 (60) |
80 (100) |
120 (150) |
